Remigo
Search
Search
Dark mode
Light mode
Reader mode
Explorer
Home
❯
02_Service steps
❯
Drivetrain Assembly
Drivetrain Assembly
34 items under this folder.
Sep 30, 2026
DT-ASM-001 STEP 1 - Inspect motor housing
Sep 30, 2026
DT-ASM-002 STEP 2 - Inspect O-ring and stator surfaces
Sep 30, 2026
DT-ASM-003 STEP 3 - Inspect stator
Sep 30, 2026
DT-ASM-004 STEP 4 - Heat motor housing
Sep 30, 2026
DT-ASM-005 STEP 5 - Insert and bond stator
Sep 30, 2026
DT-ASM-006 STEP 6 - Measure stator position
Sep 30, 2026
DT-ASM-007 STEP 7 - Inspect rotor
Sep 30, 2026
DT-ASM-008 STEP 8 - Press bearing onto rotor
Sep 30, 2026
DT-ASM-009 STEP 9 - Check pressed bearing position
Sep 30, 2026
DT-ASM-010 STEP 10 - Install external circlip
Sep 30, 2026
DT-ASM-011 STEP 11 - Install shim washer if required
Sep 30, 2026
DT-ASM-012 STEP 12 - Insert rotor into motor housing
Sep 30, 2026
DT-ASM-013 STEP 13 - Install heat sink
Sep 30, 2026
DT-ASM-014 STEP 14 - Apply thermal paste to heat sink
Sep 30, 2026
DT-ASM-015 STEP 15 - Install motor controller
Sep 30, 2026
DT-ASM-016 STEP 16 - Connect and secure cables
Sep 30, 2026
DT-ASM-017 STEP 17 - Apply silicone to PCBA area
Sep 30, 2026
DT-ASM-018 STEP 18 - Preheat bearing
Sep 30, 2026
DT-ASM-019 STEP 19 - Press bearing onto shaft
Sep 30, 2026
DT-ASM-020 STEP 20 - Measure bearing depth
Sep 30, 2026
DT-ASM-021 STEP 21 - Apply grease to bearing
Sep 30, 2026
DT-ASM-022 STEP 22 - Install wave spring washer
Sep 30, 2026
DT-ASM-023 STEP 23 - Install O-ring into housing lid
Sep 30, 2026
DT-ASM-024 STEP 24 - Apply grease to O-ring and bearing contact surface
Sep 30, 2026
DT-ASM-025 STEP 25 - Install housing lid
Sep 30, 2026
DT-ASM-026 STEP 26 - Prepare radial shaft seals
Sep 30, 2026
DT-ASM-027 STEP 27 - Check radial shaft seal orientation
Sep 30, 2026
DT-ASM-028 STEP 28 - Press radial shaft seals into housing lid
Sep 30, 2026
DT-ASM-029 STEP 29 - Inspect radial shaft seals
Sep 30, 2026
DT-ASM-030 STEP 30 - Install seal cover
Sep 30, 2026
DT-ASM-031 STEP 31 - Install housing anode
Sep 30, 2026
DT-ASM-032 STEP 32 - Install washer and shear pin
Sep 30, 2026
DT-ASM-033 STEP 33 - Install propeller and washer
Sep 30, 2026
DT-ASM-034 STEP 34 - Install safety nut and anode