Remigo
Search
Search
Dark mode
Light mode
Reader mode
Explorer
Home
❯
02_Service steps
❯
Drivetrain Service
Drivetrain Service
48 items under this folder.
Sep 30, 2026
DT-ASM-001 ASSEMBLY STEP 1 - Prepare rotor
Sep 30, 2026
DT-ASM-002 ASSEMBLY STEP 2 - Install shim washer if required
Sep 30, 2026
DT-ASM-003 ASSEMBLY STEP 3 - Insert rotor into motor housing
Sep 30, 2026
DT-ASM-004 ASSEMBLY STEP 4 - Align heat sink
Sep 30, 2026
DT-ASM-005 ASSEMBLY STEP 5 - Press heat sink into motor housing
Sep 30, 2026
DT-ASM-006 ASSEMBLY STEP 6 - Apply thermal paste to heat sink
Sep 30, 2026
DT-ASM-007 ASSEMBLY STEP 7 - Install motor controller
Sep 30, 2026
DT-ASM-008 ASSEMBLY STEP 8 - Connect and secure cables
Sep 30, 2026
DT-ASM-009 ASSEMBLY STEP 9 - Apply silicone to motor controller area
Sep 30, 2026
DT-ASM-010 ASSEMBLY STEP 10 - Preheat bearing
Sep 30, 2026
DT-ASM-011 ASSEMBLY STEP 11 - Place bearing on shaft
Sep 30, 2026
DT-ASM-012 ASSEMBLY STEP 12 - Press bearing onto shaft
Sep 30, 2026
DT-ASM-013 ASSEMBLY STEP 13 - Measure bearing depth
Sep 30, 2026
DT-ASM-014 ASSEMBLY STEP 14 - Apply grease on bearing
Sep 30, 2026
DT-ASM-015 ASSEMBLY STEP 15 - Install wave spring washer
Sep 30, 2026
DT-ASM-016 ASSEMBLY STEP 16 - Install O-rings into housing lid
Sep 30, 2026
DT-ASM-017 ASSEMBLY STEP 17 - Apply grease to O-ring and bearing contact surface
Sep 30, 2026
DT-ASM-018 ASSEMBLY STEP 18 - Install housing lid
Sep 30, 2026
DT-ASM-019 ASSEMBLY STEP 19 - Prepare radial shaft seals
Sep 30, 2026
DT-ASM-020 ASSEMBLY STEP 20 - Check radial shaft seal orientation
Sep 30, 2026
DT-ASM-021 ASSEMBLY STEP 21 - Press radial shaft seals into housing lid
Sep 30, 2026
DT-ASM-022 ASSEMBLY STEP 22 - Inspect radial shaft seals
Sep 30, 2026
DT-ASM-023 ASSEMBLY STEP 23 - Install seal cover
Sep 30, 2026
DT-ASM-024 ASSEMBLY STEP 24 - Install housing anode
Sep 30, 2026
DT-ASM-025 ASSEMBLY STEP 25 - Install washer and shear pin
Sep 30, 2026
DT-ASM-026 ASSEMBLY STEP 26 - Install propeller and washer
Sep 30, 2026
DT-ASM-027 ASSEMBLY STEP 27 - Install safety nut and anode
Sep 30, 2026
DT-ASM-028 ASSEMBLY STEP 28 - Check wave spring washer compression
Sep 30, 2026
DT-CHK-001 CHECK STEP 1 - Inspect propeller, shear pin and anode
Sep 30, 2026
DT-CHK-002 CHECK STEP 2 - Inspect bearings and radial shaft seals
Sep 30, 2026
DT-CHK-003 CHECK STEP 3 - Inspect motor controller and heat sink
Sep 30, 2026
DT-CHK-004 CHECK STEP 4 - Inspect stator and motor housing
Sep 30, 2026
DT-DIS-001 DISASSEMBLY STEP 1 - Remove anode
Sep 30, 2026
DT-DIS-002 DISASSEMBLY STEP 2 - Remove safety nut
Sep 30, 2026
DT-DIS-003 DISASSEMBLY STEP 3 - Remove washer and propeller
Sep 30, 2026
DT-DIS-004 DISASSEMBLY STEP 4 - Remove shear pin and washer
Sep 30, 2026
DT-DIS-005 DISASSEMBLY STEP 5 - Remove housing anode
Sep 30, 2026
DT-DIS-006 DISASSEMBLY STEP 6 - Remove seal cover
Sep 30, 2026
DT-DIS-007 DISASSEMBLY STEP 7 - Remove housing lid
Sep 30, 2026
DT-DIS-008 DISASSEMBLY STEP 8 - Remove radial shaft seals
Sep 30, 2026
DT-DIS-009 DISASSEMBLY STEP 9 - Remove wave spring washer
Sep 30, 2026
DT-DIS-010 DISASSEMBLY STEP 10 - Remove bearing 6202 ZZ
Sep 30, 2026
DT-DIS-011 DISASSEMBLY STEP 11 - Disconnect cables and prepare for heat sink removal
Sep 30, 2026
DT-DIS-012 DISASSEMBLY STEP 12 - Remove motor controller
Sep 30, 2026
DT-DIS-013 DISASSEMBLY STEP 13 - Remove heat sink
Sep 30, 2026
DT-DIS-014 DISASSEMBLY STEP 14 - Remove rotor
Sep 30, 2026
DT-DIS-015 DISASSEMBLY STEP 15 - Clean motor housing
Sep 30, 2026
DT-DIS-016 DISASSEMBLY STEP 16 - Remove bearing 6202 ZZ from rotor